Cold-Rolled vs Hardened & Tempered Steel Strip | BTC Strips

The choice is not between two grades. It is between two conditions of the same kind of strip — and btstrips.com publishes both. Cold-rolled (CRCA) strip is supplied annealed or rolling hard, for forming first and heat-treating afterwards. Hardened & tempered (H&T, +QT) strip is supplied already heat-treated, pre-hardened to a stated hardness, for parts that must work as springs or cutting edges without a second heat treatment.
Homepage FAQ, verified live: "Cold-rolled steel strips provide smooth surface finishes and malleable ductility for forming and bending, whereas hardened and tempered (H&T) strips undergo continuous heat-treatment to achieve high tensile strength, elastic limits, and fatigue endurance. While cold-rolled strips require secondary heat treatment by the end-user after stamping, hardened & tempered strips arrive pre-hardened with exact Rockwell/Vickers hardness values (HRC 42–52), ready for demanding spring mechanisms and cutting tools."
What cold-rolled (CRCA) means:
CRCA medium carbon: carbon 0.30–0.60%, manganese 0.50–0.70%. Grades C-40 (C 0.35–0.45), C-55 (C 0.50–0.60), C-65 (C 0.60–0.70). Thickness 0.10–6.00 mm, width 8–500 mm, bright finish, fully annealed or rolling hard as per customer requirement. Coil form; special I.D. & O.D. can be maintained; cut lengths on request.
CRCA high carbon: carbon 0.80–1.25%, manganese 0.5–0.9%. Grades C-80 (C 0.75–0.85), C-98 (C 0.90–1.05), C125 / HC21 / 125CR1 (C 1.10–1.30). Thickness 0.07–5.00 mm, width 8–500 mm (4 mm wide material can be supplied in thickness lower than 0.6 mm), bright finish, fully annealed max 200 VPN, special temper 230–270 VPN. Coil form; special I.D. & O.D. can be maintained; cut lengths on request.
What CRCA does not publish: no hardness in HRC, no tensile strength, no yield strength, no elongation and no bend test for any CRCA grade. Do not rank CRCA grades against H&T grades on strength from composition alone.
Site boundary note (the site's own wording): the medium-carbon definition caps carbon at 0.60% while C-65 is 0.60–0.70%, and C125's carbon (1.10–1.30%) sits partly above the high-carbon definition's 1.25% upper bound.
What hardened & tempered (+QT) means:
Automated thermal process: controlled austenitic heating, rapid quench into martensite, precise reheating (tempering). Certified delivery condition EN 10132-4 (+QT). Standards EN 10132-4, DIN 17222, ASTM A684, IS 2507, ISO 9001:2015.
Thickness 0.05–4.00 mm (tolerances to ±0.005 mm); width 6–550 mm (slit width tolerances to ±0.02 mm). Hardness delivery 30 HRC min to 58 HRC max, pre-tempered to customer specification. Surface: bright polished, blue (annealed tempered), brown & grey. Edge: one or both sides edge-rounded (No. 1), square (No. 3), chamfered, or deburred sheared edge. Supply: precision-wound slit coils, ID 300 / 400 / 500 mm, customised OD; cut-to-length 100–4000 mm. Export packaging: rust-preventive oil, multi-layer VCI anti-corrosion film, heat-treated wooden pallets for global sea freight.
At a glance (text rows):
Heat treatment: CRCA — none by the supplier in this condition; the end-user heat-treats after stamping. H&T — done by the supplier: austenitic heating, quench to martensite, tempering.
When it fits: CRCA — forming and bending first; parts that will be heat-treated after forming. H&T — springs and cutting edges that must work without post-stamping heat treatment.
Hardness published: CRCA — annealed max 200 VPN / special temper 230–270 VPN (high-carbon family only). H&T — per grade in HRC and HV, family range 30–58 HRC.
Tensile strength published: CRCA — not published for any grade. H&T — per grade (see table below).
Thickness: CRCA 0.07–5.00 mm (high carbon), 0.10–6.00 mm (medium carbon). H&T 0.05–4.00 mm.
Width: CRCA 8–500 mm. H&T 6–550 mm.
Do NOT compare CRCA hardness (VPN) directly with H&T figures (HRC / HV) as if they were the same scale.
Hardness and tensile strength — H&T condition only (text rows; do NOT apply to the same grade in CRCA):
C55S / C-55 (1.1204): 40–48 HRC (390–485 HV), tensile 1250–1550 MPa.
C67S / C-65 (1.1231): 42–50 HRC (415–510 HV), tensile 1300–1600 MPa.
C75S / C-75 (1.1248): 44–52 HRC (430–540 HV), tensile 1400–1700 MPa.
C100S / C-98 (1.1274): 46–54 HRC (460–580 HV), tensile 1450–1800 MPa.
50CrV4 / 50Cr4V2 (1.8159): 44–52 HRC (430–540 HV), tensile 1400–1750 MPa.
Do NOT apply the homepage's general HRC 42–52 figure to any single grade — the grade figures above replace it where published.
Which condition for which application (family-level only, confirm per grade):
CRCA medium carbon: defence products; automotive seat belts & high tensile strapping; pen clips & hair clips; safety toe caps for shoes; industrial drums & washers; shoe shanks & measuring tapes.
CRCA high carbon: surgical blades (scalpels); metal cutting band saw blades & hack saw blades; knives for cutting foam & plastics; circlips & hanger clips; textile needles; automobile components & agricultural tools.
H&T: automobile — shock absorber flapper valves, clutch plate springs, seat belt retractor springs, wiper blade steel, circlips, chain guides; wood & carpentry tools — hand saw blades, plastering trowels, circular saw blanks, band saw blades, crosscut saws, pit saw blades; stone & marble tools — gang saw blades, circular saw blanks, granite cutting blades; industrial engineering — doctor blades for paper industry, reed & discharge valves, flexible die steel, drop pins for textile machines, leather splitting knives.
How to choose — questions to send with the enquiry (as plain paragraphs, not a numbered list):
Grade and condition — CRCA annealed / rolling hard / special temper, or H&T (+QT) pre-hardened? If H&T, which hardness in the grade's published range (e.g. C55 40–48 HRC, C67 42–50 HRC, 50CrV4 44–52 HRC)?
Thickness and width — CRCA high carbon 0.07–5.00 mm, CRCA medium carbon 0.10–6.00 mm, H&T 0.05–4.00 mm; width 8–500 mm (CRCA) or 6–550 mm (H&T); and the tolerance needed (±0.005 mm / ±0.02 mm are the site-wide figures).
Will the strip be heat-treated after forming? If yes, CRCA is the condition to ask about. If no, ask for H&T and state the hardness required.
Edge, coil ID / OD, and cut lengths — H&T: ID 300 / 400 / 500 mm, CTL 100–4000 mm; CRCA: special I.D. & O.D. can be maintained, cut lengths on request.
Application — so engineering can confirm which of the family applications actually applies to the chosen grade and condition, and supply the MTC with the dispatch.
Enquiry CTA: Get a custom quote for your specific requirements. Our engineering team is ready to assist with material selection and technical specifications. Enquiry: /enquiry. Email: info@btstrips.com. Phone: +91 85849 48988. Head office: 21A, Canning Street, Ground Floor, Kolkata – 700001, West Bengal, India. Hours: Mon–Fri 10:00 AM – 7:00 PM IST; Saturday 10:00 AM – 5:00 PM IST.

BTC Admin
Metallurgy Specialist
Precision steel strip specialists and metallurgists at BTC Precision Strips, delivering precision cold rolled and hardened tempered steel solutions since 1958.
